| List of tool and machinery used in the Fitter Trade. | https://www.youtube.com/watch?v=7rWIfto_Qww |
| Personal Protective Equipment(PPE) | https://www.youtube.com/watch?v=7emUloowPl0 |
| First Aid | https://www.youtube.com/watch?v=BumbKHqXJo0 |
| Safety Signs | https://www.youtube.com/watch?v=7SAjm7qtYOw |
| Use of fire extinguisher | https://www.youtube.com/watch?v=hm8Tene9Eqc |
| Marking and Sawing | https://www.youtube.com/watch?v=ek9GSQ8J8_s |
| Filing Flat and Square (Rough finish) | https://www.youtube.com/watch?v=kxHmXF4h8A4 |
| Chipping Flat surfaces along a marked line | https://www.youtube.com/watch?v=RyAbSIH6Luc |
| Finding centre of round bar with the help of marking block | https://www.youtube.com/watch?v=4a-kAbqusZs |
| Chipping slot and oils grooves | https://www.youtube.com/watch?v=zpCAloyO43Q |
| Filling Flat,Square and parralel to an accuracy of 0.5mm | https://www.youtube.com/watch?v=JRWewIjupds |
| Chip Curve along a line mark out,key ways at various angles and cut key ways | https://www.youtube.com/watch?v=MGl6DnYUODU |
| File thin metal to an accuracy of 0.5mm | https://www.youtube.com/watch?v=8SC7O8zEmcU |
| Step filing and Matching | https://www.youtube.com/watch?v=kWFUPiOQKlQ |
| File convex and concave radius and match | https://www.youtube.com/watch?v=fbfZ5oWuJiE |
| Drilling and Tapping practice | https://www.youtube.com/watch?v=BCZGJD2JGUI |
| Marking out of simple development | https://www.youtube.com/watch?v=jXi6V8z2fgc |
| Drill on M.S flat | https://www.youtube.com/watch?v=1LyFLXSDAu0 |
| File radius and profile to suit gauge | https://www.youtube.com/watch?v=jug7EdQz5Ok |
| Counter sink,Counter bore and ream split fit (three piece fitting) | https://www.youtube.com/watch?v=wd5QxvRhn2E |
| File and make step fit ,anguler fit,angle,surfaces | https://www.youtube.com/watch?v=xEDgb9nWN80 |
| Make simple open and sliding fit | https://www.youtube.com/watch?v=OVYR3fFE_e8 |
| Enlarge hole and increase internal dia | https://www.youtube.com/watch?v=cQtUlVxlTj0 |
| Make open fiting of curved profile | https://www.youtube.com/watch?v=71FX1eGmoKY |
| Make inside square fit | https://www.youtube.com/watch?v=i_1jiGvLAcM |
| Make sliding “T” fit | https://www.youtube.com/watch?v=fnN2RAG2F9k |
| File fit -combined,open angular and sliding sides | https://www.youtube.com/watch?v=U77CKQd3XsM |
| File internal angle 30 minutes accuracy open, angular fit | https://www.youtube.com/watch?v=q6BrY-r80Oo |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
